Updates
EQ before or after compression? How to decide on every track
Ask ten engineers whether EQ goes before or after compression and you will get ten confident answers. They can all be right, because the order is not a rule. It is a choice about what the compressor should react to. Once you see it that way, you can decide in about a minute on each track.
Why the order changes the sound
A compressor does not know what is musically important. It reacts to level, and low frequencies usually carry most of the level. Put a vocal with a lot of low-end proximity through a compressor and the rumble can trigger gain reduction on the whole voice, including the consonants and the air you wanted to keep.
That is the difference between the two positions. EQ before the compressor changes what the compressor hears, so it changes how the compressor behaves. EQ after the compressor only changes the tone of what has already been compressed. The compression itself stays exactly as it was.
You can hear this in thirty seconds. Boost 100 Hz by a few dB in front of a compressor without touching anything else: it now works harder, and more often. Make the same boost after it, and the gain reduction meter does not move.
The short answer: cut first, boost after
If you want a default, this one holds up on most tracks. Cut before the compressor, to remove what should not be driving it: rumble, plosives, a boxy resonance, a ringing frequency. Boost after the compressor, to add the brightness or weight you want without pushing the compressor harder.
It works because each move is doing its job in the right place. The cut gives the compressor a cleaner signal to respond to, and the boost stays where it cannot change the dynamics you just set.
Three tracks, three decisions
Vocals. High-pass first, starting around 80 to 120 Hz depending on the voice, and take out any resonance that jumps out on certain words. Then compress. Finish with a gentle shelf on top if the voice needs air. If you boost the top end before the compressor, the bright moments hit it first, and sibilance tends to get more obvious once you add makeup gain.
Bass. Listen for the cause of the problem. If one note booms because of the instrument or the room, cut it narrowly before the compressor, so that one note stops pumping the rest of the line. If the whole part is simply uneven, compress first and shape the tone after.
Drum bus. Here EQ often goes after. A bus compressor adds punch and brings up the room and the cymbals, so the top end you hear once it is working is not the one you started with. Correct it after the compression, once you know what you are correcting. If the kick is pumping the whole bus, an EQ is the wrong answer: use the compressor’s sidechain filter, if it has one, so the detector stops reacting to the lows.
Two EQs are not cheating
There is nothing wrong with one EQ on each side of the compressor. It is a common way to work: a corrective EQ in front that removes problems, a tonal EQ after it that adds character. Keep both moves small and each one stays easy to judge. If either one needs more than a few dB, the source or the compressor setting is probably the thing to fix.
A quick test that settles it
When you are not sure, try both orders. It takes less time than arguing with yourself.
1. Set up the first order and aim for the amount of gain reduction you want, for example 3 to 4 dB on the loudest phrases.
2. Swap the two plugins. The gain reduction will change, so adjust the threshold until it matches again. Otherwise you are comparing two different amounts of compression.
3. Match the output level and listen at the same volume. Louder almost always sounds better for a few seconds, and that is exactly what you do not want to judge.
4. Listen to one specific thing: the word that jumped out, the bass note that pumped, the harshness on the snare. Keep the order that fixes it with the smallest moves.
When the problem only happens sometimes
Some problems come and go: a sibilant S, one boomy note, a harsh moment in the chorus. A static cut treats them all the time, including the moments where nothing is wrong, and compression alone cannot aim at a single frequency. This is where dynamic EQ helps, because the band only moves when the problem is there. It often removes the need for the before-or-after question altogether.
How this works with Comet Sound
EimosEq and PhoenixCompressor were designed to make these decisions visible. On EimosEq you drag the curve and read HZ, Gain and Q directly, with dynamic bands for the problems that come and go. PhoenixCompressor shows you how hard it is working, and its auto-gain helps you compare the two orders by ear rather than by volume.
A simple chain to start from: EimosEq for the cuts, PhoenixCompressor for the dynamics, then a second EimosEq for the final colour. If you would rather describe the result than move the controls, Comet Sound AI can propose the moves on both plugins, and nothing changes until you have previewed and confirmed it.
Further along the chain, the same logic of choosing the right tool for each job applies to saturation on vocals and to clipping and limiting on the master. Both plugins are available individually and in Orbit Suite, and the Base and Pro plans include a 7-day free trial.
Comet Sound